Your new White Rodgers 5-Day/2-Day Digital Multi-stage Thermostat uses the technology of a solid-state microcomputer to provide precise time/temperature control. This thermostat offers you the flexibility to design heating and cooling programs that fit your needs. Features separate 5-day (weekday) and 2-day (weekend) programming with four separate time/temperature periods per program, simultaneous heat and cool program storage, optional C terminal (dual power option), preprogrammed temperature control, LCD continuously displays set point, and alternately displays time and room temperature. Compatible with heat/cool systems with up to two stages heat, two stages cool. Requires 2 AA batteries. Below are the key specifications, installation, operation, programming, and troubleshooting instructions.
Assemble tools required: hand or power drill with 3/16 inch drill bit (if needed), flat blade screwdriver, wire cutter/stripper.
WARNING: Failure to follow and read all instructions carefully before installing or operating this control could cause personal injury and/or property damage.
ATTENTION: This product does not contain mercury. However, this product may replace a unit which contains mercury. Do not open mercury cells. If a cell becomes damaged, do not touch any spilled mercury. Wearing non-absorbent gloves, take up the spilled mercury and place into a container which can be sealed. Mercury must not be discarded in household trash. Refer to www.white-rodgers.com for location to send product containing mercury.
ELECTRIC HEAT SYSTEMS: This thermostat is configured from the factory to operate a heat/cool, fossil fuel (gas, oil, etc.), forced air system. It is configured correctly for any system that DOES NOT require the thermostat to energize the fan on a call for heat. If your system is an electric or heat-pump system that REQUIRES the thermostat to turn on the fan on a call for heat, locate the GAS/ELECTRIC switch and switch it to the ELECTRIC position. This will allow the thermostat to energize the fan immediately on a call for heat. If you are unsure if the heating/cooling system requires the thermostat to control the fan, contact a qualified heating and air conditioning service person.
HYDRONIC (HOT WATER OR STEAM) HEATING SYSTEMS: This thermostat is set to operate properly with a forced-air heating system. If you have a hydronic heating system (a system that heats with hot water or steam), you must set the thermostat to operate properly with your system. The factory default setting is forced air heat. Change the second option in the configuration menu to SL.
BATTERY LOCATION: 2 “AA” alkaline batteries are included in the thermostat at the factory with a battery tag to prevent power drainage. You must remove the battery tag to engage the batteries. If BATT is displayed, the batteries are low and should be replaced with fresh “AA” Energizer® alkaline batteries. To replace batteries, install the batteries along the top of the base. The batteries must be installed with the positive (+) end to the left.
The thermostat consists of two parts: the thermostat cover and the base. To remove the cover, gently pull it straight out from the base. To replace the cover, line up the cover with the base and press gently until the cover snaps onto the base.
The Thermostat Buttons and Switches:
The Display:
NOTE: The following wiring diagrams show typical terminal identification and wiring. For proper installation, refer to the original manufacturer's instructions. * The 24 Volt neutral connection to terminal C on the thermostat is not required if you replace the batteries once a year with fresh “AA” Energizer® alkaline batteries. Relay contacts shown are thermostatically operated.
Figure 2. Typical wiring diagram for single transformer systems
Thermostat terminals: C*, R, B, O, Y, G, W. System: Energized in HEAT (Heating System), Energized in COOL (Cooling System), Fan Relay. Transformer: 24 VAC (Hot, Neutral), 120 VAC. Single transformer setup with connections to heating, cooling, and fan systems.
Figure 3. Typical wiring diagram for two-transformer systems with NO safety circuits
Thermostat terminals: B, C*, R, Y, G, O, W. System: Energized in COOL (Cooling System), Energized in HEAT (Heating System), Fan Relay. Transformers: 24 VAC (Hot, Neutral) for heating, 120 VAC (Hot, Neutral) for cooling. Note: CUT AND TAPE OFF! TWO COMMONS MUST BE JUMPERED TOGETHER!
Figure 4. Typical wiring diagram for two-transformer systems with safety circuits in BOTH systems
Thermostat terminals: B, C*, R, Y, G, O, W. System: Energized in COOL (Cooling System), Energized in HEAT (Heating System), Fan Relay, Accessory Relay N.O. Contact. Transformers: HEATING TRANSFORMER (24 VAC Hot, Common, Neutral), COOLING TRANSFORMER (24 VAC, 120 VAC Hot, Neutral). Safety: Limit or Safety Switches in both systems. Note: TWO COMMONS MUST BE JUMPERED TOGETHER!
NOTE: To prevent static discharge problems, touch side of thermostat to release static build-up before touching any keys. If at any time during testing your system does not operate properly, contact a qualified service person.
If your system does not have a G terminal connection, skip to Heating System.
CAUTION: To prevent compressor and/or property damage, if the outdoor temperature is below 50°F, DO NOT operate the cooling system.
This section will help you plan your thermostat’s program to meet your needs. For maximum comfort and efficiency, keep the following guidelines in mind when planning your program. When heating (cooling) your building, program the temperatures to be cooler (warmer) when the building is vacant or during periods of low activity. During early morning hours, the need for cooling is usually minimal.
Look at the factory preprogrammed times and temperatures shown below. If this program will suit your needs, simply press the RUN button to begin running the factory preset program.
Set Current Time and Day
Enter Heating Program
Enter Cooling Temperatures
CAUTION: If the outside temperature is below 50°F, disconnect power to the cooling system before programming. Energizing the air conditioner compressor during cold weather may cause personal injury or property damage.
Check your programming
SAMPLE Heating/Cooling Schedule Plan (Factory Program)
| Period | WEEKDAYS (5 Day) Start Time | WEEKDAYS Temp | SATURDAY (1 Day) Start Time | SATURDAY Temp | SUNDAY (1 Day) Start Time | SUNDAY Temp |
|---|---|---|---|---|---|---|
| 1ST | 6:00 AM | 70 F | 6:00 AM | 70 F | 6:00 AM | 70 F |
| 2ND | 8:00 AM | 62 F | 8:00 AM | 70 F | 8:00 AM | 70 F |
| 3RD | 5:00 PM | 70 F | 5:00 PM | 62 F | 5:00 PM | 62 F |
| 4TH | 10:00 PM | 62 F | 10:00 PM | 62 F | 10:00 PM | 62 F |
Reset Operation: If a voltage spike or static discharge blanks out the display or causes erratic thermostat operation you can reset the thermostat by pressing up, down and TIME at the same time. This also resets the factory defaults. If the thermostat has power, has been reset and still does not function correctly contact your heating/cooling service person or place of purchase.
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| No Heat/No Cool/No Fan (common problems) | 1. Blown fuse or tripped circuit breaker. 2. Furnace power switch to OFF. 3. Furnace blower compartment door or panel loose or not properly installed. | Replace fuse or reset breaker. Turn switch to ON. Replace door panel in proper position to engage safety interlock or door switch. |
| No Heat | 1. Pilot light not lit. 2. System Switch not set to Heat. 3. Loose connection to thermostat or system. 4. Furnace Lock-Out Condition. Heat may also be intermittent. | Re-light pilot. Set System Switch to Heat and raise temp above room temp. Verify thermostat and system wires are securely attached. Many furnaces have safety devices that shut down when a lock-out condition occurs. If the heat works intermittently contact the furnace manufacturer or local service person for assistance. |
| No Heat (continued) | 5. Heating system requires service or thermostat requires replacement. | Diagnostic: Set System Switch to Heat and raise the setpoint above room temperature. Within a few seconds the thermostat should make a soft click sound. This sound usually indicates the thermostat is operating properly. If the thermostat does not click, try the reset operation listed above. If the thermostat does not click after being reset contact your heating and cooling service person or place of purchase for a replacement. If the thermostat clicks, contact the furnace manufacturer or a service person to verify the heating is operating correctly. |
| No Cool | 1. System Switch not set to Cool. 2. Loose connection to thermostat or system. 3. Cooling system requires service or thermostat requires replacement. | Set System Switch to Cool and lower temp below room temp. Verify thermostat and system wires are securely attached. Same procedure as diagnostic for No Heat condition except set the thermostat to Cool and lower the setpoint below the room temperature. There may be up to a five minute delay before the thermostat clicks in Cooling. |
| Heat, Cool or Fan Runs Constantly. | 1. Possible short in wiring. 2. Possible short in thermostat. 3. Possible short in heat/cool/fan system. 4. Fan Switch set to Fan On. | Check each wire connection to verify they are not shorted or touching together. No bare wire should stick out from under terminal screws. Try resetting the thermostat as described below. If the condition persists the manufacturer of your system or service person can instruct you on how to test the Heat/Cool system for correct operation. If the system operates correctly, replace the thermostat. |
| Furnace Cycles Too Fast or Too Slow (narrow or wide temperature swing) | 1. The location of the thermostat and/or the size of the Heating System may be influencing the cycle rate. | Digital thermostats normally provide precise temperature control and may cycle faster than some older mechanical models. A faster cycle rate means the unit turns on and off more frequently but runs for a shorter time so there is no increase in energy use. If you would like to increase the cycle time, change the cycle rate to “SL” in the configuration menu. |